BIOFLO 4500 MANUAL PDF

The abundant information provided by the analytical ultracentrifugation can assess the sample heterogeneity aggregation and purifymolecular conformation folded or unfoldedcomposition assembled or unassembledand thermodynamic properties of the interacting systems. But without actually testing the fermenter in its entirety it is hard to guarantee it beyond our basic testing. This Item is no longer available. Sign In or Register. Quick Stop Auctions, Inc. The fermenter has quite a few solenoids, but it looks to be missing some of the instrumentation wires that would connect to the front of the controller.

Author:Arasida Zurr
Country:Cuba
Language:English (Spanish)
Genre:Video
Published (Last):25 January 2008
Pages:276
PDF File Size:17.69 Mb
ePub File Size:20.28 Mb
ISBN:275-6-67177-627-4
Downloads:84361
Price:Free* [*Free Regsitration Required]
Uploader:Mogal



Page 7: Operating Controls And Displays 1. There are twenty keys on the keypad. The function of "Screen" key is to select the screen. There are three screens which can be selected on the display. The first one is the "Master" screen, the other two are: a "Calibration" Page 8 making these selections, move the cursor to the loop or the mode to be changed, then press the "Alter" key to get the desired selection and then press "Enter" key.

If you have a loop set already, you cannot change into that loop. Read NOTE: 1. Change function to zero, calibrate zero. Change function to span, calibrate span. Figure 16 There is a recorder output connector on the left hand side of the control cabinet. An external recorder with volt high impedance input may be connected to the output. Position the BioFlo console on a firm level surface in an area where services are readily available.

Level the horizontal surface of the base with four leveling glides if necessary. It is by means of this connector that an external computer may communicate with and control the BioFlo Fermentor.

Pin designations are as follows Fill the vessel with a mild detergent and water solution. Let stand for one hour then scour thoroughly. Check the level of the reference electrolyte. It should be about 1cm below the filling orifice, which is closed with a rubber "T" stopper. To add reference electrolyte, take the filling pipette P and fill it with Viscolyte B P Electrolyte. Connect electrode to the pH connector using the appropriate cable.

Turn ON the main power switch. Display calibration screen. Page 17 sampler valve. Sterilize the complete assembly consisting of jar, headplate and components of headplate by inserting in an autoclave.

NOTE: For continuous culture, vessel should not be sterilized empty. Use at least mL of sterilized water. Probe tips must be moist during sterilization. After autoclaving medium will be brought from the medium reservoir, sterilized separately. Page Dissolved Oxygen Electrode d. Calibration O2 amplifier for polarization purpose prior to calibration. The electrode is polarized and ready for operation after six hours of polarization time. There are two methods of obtaining zero on the BioFlo Use either Method 1 or Method 2.

Method 1 Remove the D. Page Cascade System C. Add glycerin to the thermowell and insert RTD temperature probe. Turn on the water valve, adjust water pressure to 20 PSI. Connect air and O2 to the unit, adjust gas pressure to 10 PSI. Page Sampling Procedure 3. Cascade System To set up, proceed as follows: Set agitation and D.

Set agitation to the minimum RPM you wish for D. Change agitation mode to D. Set agitation speed to maximum RPM you wish for D. Page Operation Tips 2. Set the agitation, temperature to "OFF". Turn off the power. If the system is not to be used for several days, disconnect power plug. Remove and clean vessel, and associated components as outlined in previous steps. Calibrate DO to and allow it to stabilize. The DO reading drops very quickly. When DO returns to 50, stop counting time.

When periodically performed, it will result in longer life for the equipment and reduce time lost due to equipment failure. Use a damp cloth moistened with water or mild detergent. It should be about 1cm below the filling orifice. To add solution, see section 3. The probe should be stored standing upright. The two rubber "T" Total Volume M 2. One of the following items should be selected. One of the following Perfusion Kits could be selected.

Perfusion Kit for Cell Lift Application. NBS Part No.

ASTM E466-96 PDF

Search, browse, and buy used lab equipment from BioSurplus Inc.

Page 7: Operating Controls And Displays 1. There are twenty keys on the keypad. The function of "Screen" key is to select the screen. There are three screens which can be selected on the display. The first one is the "Master" screen, the other two are: a "Calibration"

BIRMAN SCHIPER STEPHENSON PROTOCOL PDF

New Brunswick Scientific BioFlo 4500 Manuals

Used — Used Date updated: Our Avestin EmulsiFlex C5 homogenizer can be used for cell rupture, preparation of liposomes, dispersion or emulsion of materials. As such, buyer has the option of either having the unit shipped via freight, or picking it up in person from our warehouse here in Virginia. Need to ship this item? Feel free to ask questions via email or The fermenter has quite buoflo few solenoids, but it looks to be missing some of the instrumentation wires that would connect to the front of the controller. If there is anything that any potential bidders would like checked out specifically about this unit we can help out with that. The Proteome XL-I analytical ultracentrifuge in biofll facility can characterize a variety of biophysical properties of macromolecules such as molecular weight, sedimentation coefficient, diffusion coefficient, equilibrium constant and stoichiometry.

KRIZA E EUROZONES PDF

BIOFLO 4500 MANUAL PDF

Vojora Some unique features of fermentor are: Used — Used Date updated: DOTmed has partnered with uShip to get you the best quotes from reliable shippers. Feel free to ask questions via email or Some unique features of fermentor are:. New Brunswick BioFlo mxnual 20L capacity for bacterial and yeast cell growth The increase of recombinant protein expression in fermentor is largely due to the increase of biomass production under the optimized growth condition. The lister has indicated that this item is no longer available. January 30, You can also: As such, buyer has the option of either having the unit shipped via freight, or picking it up in person from our warehouse here in Virginia.

TEKLA BASIC TRAINING PDF

Brunswick BIOFLO 3000 Manual To Operations

.

Related Articles